49 WIRELESS 433 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this revolutionary 433MHz temperature Stati
58 Alarm key (al) • Press and hold for 3 seconds to enter the alarm setting mode. • In alarm setting mode, press to toggle between the following se
59 Time reception icon (for DCF time)Outdoor data signal reception indicatorOutdoor transmitter identification numberLCD Screen: The LCD screen is
60 MANUAL SETTINGS: In normal display mode, press and hold the OK key for 3 seconds to enter the manual setting mode for the following: a. LCD cont
61 LCD CONTRAST SETTING: The LCD contrast can be set within 8 levels, from LCD 0 to LCD7 (Default setting is “LCD 5”): 1. In normal di
62 TIME ZONE SETTING: The time zone default of the Temperature Station is “0”. To set a different time zone: 1. Press and hold the OK k
63 DAYLIGHT SAVING TIME SETTING 1. Press and hold the OK key until the digits “Lcd” starts flashing. 2. Press shortly the OK key two
64 TIME RECEPTION ON/OFF SETTING: In area where reception of the DCF time is not possible, the DCF time reception function can be turned
65 12/24-HOUR FORMAT SETTING: The time display can be selected to show hours in 12-hour or 24-hour settings. (Default 24-Hour) 1. Press
66 Hour flashing Minutes flashing MANUAL TIME SETTING: In case the Temperature Station cannot detect the DCF-signal (for example due to disturbances
67 Note: The unit will still try and receive the signal every day despite it being manually set. When it does receive the signal, it will change th
50 • DCF radio controlled time with manual setting option • Time zone option ±12 hours • Indoor and outdoor temperature display with MIN/MAX records
68 4. Press the OK key one more time to confirm the year and advance to the month setting. The month digit will be flashing. 5. Use the Plus and
69 RECORDING INTERVAL (hr:min) SETTING The time intervals at which the temperature and humidity data saved to memory can be set to one
70 1. Press and hold the OK key until the digits “Lcd” starts flashing. 2. Press and release the OK key eleven times to enter minute setting of t
71 3. Press Plus to get in Learn/ Remove setting of channels. The channel icon “1” will be flashing. 4. Press OK key () to select another chan
72 Up to 5 outdoor transmitters can be received by the temperature station. User may decide the number of transmitter data to be save to the perman
73 TOGGLING BETWEEN DIFFERENT CHANNELS (INDOOR AND OUTDOOR CHANNELS): 1. Press the Plus or Minus key to toggle between the Temperature and humidity
74 VIEWING VARIOUS TYPE OF TEMP/HUMDITY READINGS OF A SELECTED CHANNEL: After a particular channel (the indoor sensor or one of the outdoor transmit
75 b. The Min temperature and Min humidity In normal display mode, press the mode key two times. The minimum temperature and humidity
76 c. The average value of the last 100 sets reading In normal display mode, press the mode key three times. The average temperature a
77 d. The dew point temperature In normal display mode, press the mode key four times. The dew point temperature will be displayed n
51 The Outdoor Temperature Transmitter (purchased seperately) • Remote transmission of outdoor temperature and humidity to Temperature Station by 43
78 e. The history data sets of temperature and humidity In normal display mode, press the mode key five times. The “hist” icon will
79 CALIBRATION OF TEMPERATURE AND HUMIDITY READING The temperature station allows user to calibrate the displayed temperature and humidity readings
80 To calibrate the temperature reading: 1. Press the Plus or Minus key to select a channel (the sensor at the temperature station or one of the ou
81 To set the high humidity alarm: 1. In normal display, press the Plus or Minus key to select a channel (the sensor at the temperature station or
82 2. Press and hold the Alarm key for about 3 second to enter high humidity alarm setting. Then press the Alarm key shortly one more time to enter
83 3. Press the Mode key to select to “activate” or “deactivate” the low temperature alarm. (“Alarm On” or “Alarm Off” icon will be displayed) 4.
84 CLEAR DATA IN THE TEMPERATURE STATION CLEARING THE MAX/MIN TEMPERATURE AND HUMIDITY DATA OF A PARTICULAR CHANNEL To clear the max
85 1. Press and hold the Mode key for 5 second. The maximum and minimum temperature/ humidity data and the time of record will be reset to the curr
86 3. The running digits will be displayed for about 6 minutes, followed by the full segment display. User is then required to remov
87 The display will show some running digits when the temperature station is reset. Full segment will be displayed- user
52 Battery compartment HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER The Outdoor Temperature transmitter uses 2 x AA. IEC LR6,
88 After batteries are re-inserted, the station will automatically launch the learn mode. The signal receipt indicator will be displayed. User needs
89 CHECKING FOR 433MHz RECEPTION If the outdoor temperature data is not being received within three minutes after setting up (or outdoor display sho
90 POSITIONING THE TEMPERATURE STATION: The Temperature Station provides the option of table standing or wall mounting the unit. Before wall mountin
91 The mounting surface can affect the transmission range. If e.g. the unit is attached to a piece of metal, it may either reduce or increase the tr
92 SPECIFICATIONS: Temperature measuring range: Indoor : -9.9ºC to +59.9ºC with 0.1°C resolution +14ºF to +139.8ºF with 0.2ºF resolution
93 LIABILITY DISCLAIMER • The electrical and electronic wastes contain hazardous substances. Disposal of electronic waste in wild country and/or in
94 R&TTE Directive 1999/5/EC Summary of the Declaration of Conformity : We hereby declare that this wireless transmission device does comply wi
53 BATTERY CHANGE: User shall replace batteries of the temperature station when the battery low indicator is displayed at the LCD. If user does not
54 Note: If the indoor temperature and humidity are not displayed after 15 seconds, remove the batteries and wait for at least 2 minutes before re
55 7. If after 10 minutes, the DCF time has not been received, press and hold the OK () key for 3 seconds to enter the Set up mode for manual time
56 FUNCTION KEYS: Temperature Station: There are 5 function keys in the Temperature Station: OK key ( ) • In normal display mode, p
57 i. Recording intervals to memory (hr:min) j. Re-learning/ Removing channels k. Number of channels to be saved to memory • In view mode or alar
Commentaires sur ces manuels